Sensibulb is the first LED cabin bulb replacement unit to directly replace the performance of halogen and xenon bulbs without the hazardous heat, high power consumption or UV emissions. Available in Red or White.

Sensibulb Specification:
   • Size: 1.00" x 1.00" x 5/8"
   • Weight: 0.3 oz (20g)
   • Typical Current Usage: 0.16 Amps(warm) - 0.2 Amps(cold)                      
   • Voltage Range: 10-32 Volts DC
   • Typical Operating Temperature: 140° F
   • Ultra Violet Emissions: 0.00

More Info                $39.95

This adapter allows you to upgrade your old bayonet style socket to a G4 bipin socket to fit the Sensibulb LED light. Available in Single or Double Pin Style.  Please Specify

$1.95

This bracket adapts our Sensibulb to fit both the standard 2-pin G4 sockets and the older style bayonet sockets commonly used in berth lights and reading lights. The bracket clips snugly around the outside of these sockets (approximately 5/8" or 15 mm diameter) and provides a secure mount for your new Sensibulb.
Chances are extremely good that your fixture has one of these sockets and that this little bracket will snap right on.  It's simple: Remove your old light bulb, clip the Mounting Bracket to the outside of the socket, plug in and mount your new Sensibulb. You're done!

$3.95

Edison Screw to G4 Socket Adaptor (Use with 12 VDC systems with Sensibulb
Covert your screw light bulb fixtures with this adapter to fit Sensibulbs

$2.95

 

This kit allows you to use the dimmer function of the Sensibulb.

Kit includes mini-controller, control know and installation instructions.  Unit plugs into any Sensibulb and allows you to turn your power consumption down even further to 0.025amps!

Note: Installation requires the drilling of one slightly enlarged 1/4" hole on the side of the fixture to accommodate the control knob.

$22.95

LED TriColor Navigation and Anchor Light (without daylight photo sensor) USCG Approved!!

This LED TriAnchor combination light is completely waterproof, rugged, and low-power. Draws only 0.5Amp at 12V. Separate colored and white LED's allow selection of tricolor or anchor in a single low-profile design.

Operates on 12 VDC. Call for 24V operation.
 

$239.00

LED TriColor Navigation and Anchor Light (with daylight photo sensor) USCG Approved!!

Optional: Same TriAnchor light as above, with addition of a photodiode to automatically turn anchor light on at night. Uses ultra long-life photodiode as opposed to the more common CdS photocell for years of trouble-free operation.

Operates on 12 VDC. Call for 24V operation.

$269.00

 

LED TriColor Navigation and Anchor Light.  With emergency Strobe (without daylight photo sensor) USCG Approved!!

Optional: Same popular LED TriAnchor light with the addition of a strobe. The three bright white LED'S that make up the anchor portion of this light blink at a 1 second interval when the strobe is activated. The first and only TriColor/Anchor/Strobe Light to operate using only 3 wires. Selector Switch strongly recommend for strobe versions.

Operates on 12 VDC. Call for 24V operation.

$339.00

LED TriColor Navigation and Anchor Light.  With emergency Strobe (with daylight photo sensor) USCG Approved!!

Optional: This light has all the features: Ultra long life photodiode to automatically turn the anchor portion on at night, strobe for emergencies, and all the rugged low-power features of our other LED TriAnchor lights. Selector Switch strongly recommend for strobe versions

Operates on 12 VDC. Call for 24V operation.
 

$369.00

 

This bracket mounts to the top of the mast with two screws, and supports the Anchor or TriAnchor light. Multiple drilled holes in top allow mounting light at various orientations. Constructed of 316 stainless steel.

$20.00

This bracket mounts to the side of the mast with two screws, and supports the Anchor or TriAnchor light. Multiple drilled holes in top allow mounting light at various orientations. Constructed of 316 stainless steel.

$30.00

 

2 Wire Switch for LED Masthead TriColor Navigation / Anchor Light.  For applications where an old 2-wire Anchor light is replaced with a TriAnchor without changing your mast wiring.

Many older boats have masts that are wired with a two conductor wire going up to the masthead. In the past it was impossible to have both Tricolor and an Anchor light because you only had a single +/- going up to the masthead and down to the switch panel.
Since LED's ostensibly are just diodes, namely, one-way streets for electrons this is no longer an issue.
This nifty little switch is a simple DPDT switch that is wired to reverse the polarity of your existing two-conductor mast wiring.The TriAnchor is designed to accept +/- or -/+ giving you the Tricolor or Anchor light function respectively
 

$25.00

3-wire Optional Selector Switch for TriAnchor Light with Strobe . Function switch rotates between "Tri-color", "Anchor", "Strobe" and "off" functions.

This switch is not necessary in application where panel switched for "Tricolor" and "Anchor" already exist.  Typically if you are replacing your existing "Antique" TriAnchor light you will not need this switch since turning the Tri-Color panel switch and Anchor light panel switch "on" at the same time this will cause the "Strobe" to Function.

Use this switch in application where separate panel switches for "Tri-Color" and "Anchor" do not exist and you have purchased a Tri-Anchor unit with Strobe.

$30.00